Upcoming Training & Events

25 - 26 Nov 2024

2 days

New to Ansys Mechanical? This is the place to start. After completing this course you’ll understand the complete end-to-end procedure for conducting basic linear static structural analyses and will be able to apply it to the solution of your own analysis problems. Just as importantly, you’ll learn several techniques to improve the efficiency of your solutions and the fidelity of your results. You’ll also have a firm foundation for studying many advanced analysis techniques in Ansys Mechanical

25 - 26 Nov 2024

2 days

Is thermal management critical to your design? Are you concerned with the effects of heat on structures? This is the place to start. This course will help you develop the skills necessary to predict the thermal response of structures to various heat loads using Ansys Mechanical. You’ll learn complete solution procedures for conduction, natural convection, and radiation heat transfer under both steady-state and time-varying conditions. Lastly, you’ll explore several methods of performing thermal stress a

25 - 29 Nov 2024

5 days

This course is designed for new users who want to become proficient with Creo Parametric as quickly as possible.

25 - 29 Nov 2024

5 days

We recommend the 5-day Introduction to Creo Parametric course for those with limited or no previous experience in 3D CAD systems. From this course they will quickly gain confidence in creating models using Creo Parametric.

25 - 26 Nov 2024

2 days

Learn how to use surfaces to create models in Creo.

25 - 27 Nov 2024

6 hours 3 x 2 hour sessions

Failure Mode and Effects Analysis (FMEA) is bottom up, inductive failure analysis that considers the effect that failure of lower level components and assemblies will have on the overall system. This technique is used across engineering to understand how systems can fail, the causes of failure and to identify the best ways to reduce risk.

27 - 28 Nov 2024

2 days

Learn how to create schematic diagrams using Creo Parametric for both Electrical harness creation and piping layouts

2 - 3 Dec 2024

2 days

Solve heat transfer problems involving conduction, convection (forced and natural) and radiation, including heat transfer theory, the definition of thermal boundary conditions, and model selection and setup for radiation and natural convection.

2 - 3 Dec 2024

2 days

This course will enable you to achieve and understand simulation analysis with contact, giving you the knowledge for preprocessing full solutions and post-processing.

Mon 2 Dec 2024

1 day

Learn the new features and enhancements in Part Modelling, Assembly, Drawing, Surfacing, Sheet Metal, Rendering along with Multi-Body Design and enhancements in the Mini Toolbar.

2 - 4 Dec 2024

6 hours 3 x 2 hour sessions

The field of electromagnetic compatibility is a critical yet often ignored technical discipline. Every person involved in the development, manufacture and through life support of a product can have a significant but unknowing effect on the EMC performance of a product.

2 - 3 Dec 2024

6 hours 2 x 3 hour sessions

Fatigue is the most common cause of structural failure in parts subjected to repeated loadings. During this concise one day course, you will learn about the fundamentals of fatigue and the methodologies which can be used to predict the number of cycles before failure occurs. With the knowledge gained, you will be suitably equipped to design against fatigue failures.

Mon 2 Dec 2024

1 day

Basic eBOM Management - Gain an understanding of the eBOM creation process.

3 - 5 Dec 2024

3 days, 9:00 AM - 5:00 PM

This course teaches the essential skills you will need to start performing basic computational fluid dynamics (CFD) simulations on your own using Ansys CFX software.

Tue 3 Dec 2024

1 day

This course is intended for participants with little or no experience of using HAZOP as well as managers, supervisors, engineers and technicians with at least a little understanding of both engineering design and technical safety (for example, interlocks, permissives and trips). This includes for the system to be studied an understanding of: the engineering principles the design intent the design representation of the system being studied, for example a detailed assembly drawing and the modes of

3 - 4 Dec 2024

2 days

Reliability Engineering emphasises dependability in the lifecycle management of a product, where it is essential to consider the Reliability, Availability and Maintainability (RAM) characteristics. RAM analysis contains a number of techniques that help engineers understand the risks that will prevent dependable operation of a system by assessing failure modes, frequencies and consequences.

3 - 4 Dec 2024

2 days

Understand how to use Workflow tools. Create Workflow templates and define tasks.

4 - 5 Dec 2024

5 hours 2 x 2.5 hour sessions

This course is designed to provide knowledge about the optimization workflow in Ansys Workbench. The complete end-to-end procedure is shown from the original CAD to the final calculation of the optimized shape.

4 - 5 Dec 2024

4 hours 2 x 2 hour sessions

Defective plastic parts are often only found late in the day and after significant investment of time and money. This online version of our well established classroom-based course will help you develop an understanding of the causes of part defects and how to avoid them. Common plastic part defects will be explored and solutions developed, enabling attendees to design plastic parts with confidence.

Wed 4 Dec 2024

1 day

Process Safety Management is a key leading indicator for plants which are exposed to hazards as a result of their operations. These hazards include flammable and explosive materials, high pressure, high and low temperatures, contaminants and toxic substances.

Thu 5 Dec 2024

1 day

Ansys Discovery is a first-of-its-kind virtual prototyping environment providing interactive design exploration early in the development process for both structural and fluid flow analysis.

Thu 5 Dec 2024

1 day

Learn how to use the new Creo 7 Multi-Body functionality

9 - 11 Dec 2024

3 days

This course teaches you how to use Advanced Part Modelling Techniques to improve your product designs.

9 - 13 Dec 2024

5 days

This course is designed for new users who want to become proficient with Creo Parametric as quickly as possible.