Upcoming Training & Events

25 - 26 Nov 2024

2 days

New to Ansys Mechanical? This is the place to start. After completing this course you’ll understand the complete end-to-end procedure for conducting basic linear static structural analyses and will be able to apply it to the solution of your own analysis problems. Just as importantly, you’ll learn several techniques to improve the efficiency of your solutions and the fidelity of your results. You’ll also have a firm foundation for studying many advanced analysis techniques in Ansys Mechanical

25 - 26 Nov 2024

2 days

Is thermal management critical to your design? Are you concerned with the effects of heat on structures? This is the place to start. This course will help you develop the skills necessary to predict the thermal response of structures to various heat loads using Ansys Mechanical. You’ll learn complete solution procedures for conduction, natural convection, and radiation heat transfer under both steady-state and time-varying conditions. Lastly, you’ll explore several methods of performing thermal stress a

25 - 29 Nov 2024

5 days

This course is designed for new users who want to become proficient with Creo Parametric as quickly as possible.

25 - 29 Nov 2024

5 days

We recommend the 5-day Introduction to Creo Parametric course for those with limited or no previous experience in 3D CAD systems. From this course they will quickly gain confidence in creating models using Creo Parametric.

25 - 26 Nov 2024

2 days

Learn how to use surfaces to create models in Creo.

25 - 27 Nov 2024

6 hours 3 x 2 hour sessions

Failure Mode and Effects Analysis (FMEA) is bottom up, inductive failure analysis that considers the effect that failure of lower level components and assemblies will have on the overall system. This technique is used across engineering to understand how systems can fail, the causes of failure and to identify the best ways to reduce risk.

27 - 28 Nov 2024

2 days

Learn how to create schematic diagrams using Creo Parametric for both Electrical harness creation and piping layouts

2 - 3 Dec 2024

2 days

Solve heat transfer problems involving conduction, convection (forced and natural) and radiation, including heat transfer theory, the definition of thermal boundary conditions, and model selection and setup for radiation and natural convection.

2 - 3 Dec 2024

2 days

This course will enable you to achieve and understand simulation analysis with contact, giving you the knowledge for preprocessing full solutions and post-processing.

Mon 2 Dec 2024

1 day

Learn the new features and enhancements in Part Modelling, Assembly, Drawing, Surfacing, Sheet Metal, Rendering along with Multi-Body Design and enhancements in the Mini Toolbar.

2 - 4 Dec 2024

6 hours 3 x 2 hour sessions

The field of electromagnetic compatibility is a critical yet often ignored technical discipline. Every person involved in the development, manufacture and through life support of a product can have a significant but unknowing effect on the EMC performance of a product.

2 - 3 Dec 2024

6 hours 2 x 3 hour sessions

Fatigue is the most common cause of structural failure in parts subjected to repeated loadings. During this concise one day course, you will learn about the fundamentals of fatigue and the methodologies which can be used to predict the number of cycles before failure occurs. With the knowledge gained, you will be suitably equipped to design against fatigue failures.

Mon 2 Dec 2024

1 day

Basic eBOM Management - Gain an understanding of the eBOM creation process.

3 - 5 Dec 2024

3 days, 9:00 AM - 5:00 PM

This course teaches the essential skills you will need to start performing basic computational fluid dynamics (CFD) simulations on your own using Ansys CFX software.

Tue 3 Dec 2024

1 day

This course is intended for participants with little or no experience of using HAZOP as well as managers, supervisors, engineers and technicians with at least a little understanding of both engineering design and technical safety (for example, interlocks, permissives and trips). This includes for the system to be studied an understanding of: the engineering principles the design intent the design representation of the system being studied, for example a detailed assembly drawing and the modes of

3 - 4 Dec 2024

2 days

Reliability Engineering emphasises dependability in the lifecycle management of a product, where it is essential to consider the Reliability, Availability and Maintainability (RAM) characteristics. RAM analysis contains a number of techniques that help engineers understand the risks that will prevent dependable operation of a system by assessing failure modes, frequencies and consequences.

3 - 4 Dec 2024

2 days

Understand how to use Workflow tools. Create Workflow templates and define tasks.

4 - 5 Dec 2024

5 hours 2 x 2.5 hour sessions

This course is designed to provide knowledge about the optimization workflow in Ansys Workbench. The complete end-to-end procedure is shown from the original CAD to the final calculation of the optimized shape.

4 - 5 Dec 2024

4 hours 2 x 2 hour sessions

Defective plastic parts are often only found late in the day and after significant investment of time and money. This online version of our well established classroom-based course will help you develop an understanding of the causes of part defects and how to avoid them. Common plastic part defects will be explored and solutions developed, enabling attendees to design plastic parts with confidence.

Wed 4 Dec 2024

1 day

Process Safety Management is a key leading indicator for plants which are exposed to hazards as a result of their operations. These hazards include flammable and explosive materials, high pressure, high and low temperatures, contaminants and toxic substances.

Thu 5 Dec 2024

1 day

Ansys Discovery is a first-of-its-kind virtual prototyping environment providing interactive design exploration early in the development process for both structural and fluid flow analysis.

Thu 5 Dec 2024

1 day

Learn how to use the new Creo 7 Multi-Body functionality

9 - 11 Dec 2024

3 days

This course teaches you how to use Advanced Part Modelling Techniques to improve your product designs.

9 - 13 Dec 2024

5 days

This course is designed for new users who want to become proficient with Creo Parametric as quickly as possible.

Mon 9 Dec 2024

1 day

Failure Mode and Effects Analysis (FMEA) is bottom up, inductive failure analysis that considers the effect that failure of lower level components and assemblies will have on the overall system. This technique is used across engineering to understand how systems can fail, the causes of failure and to identify the best ways to reduce risk.

Mon 9 Dec 2024

1 day

Understand PDMLink from a Creo user's perspective.

Mon 9 Dec 2024

0.5 day

Introduction to Windchill

9 - 11 Dec 2024

3 days, 9:30 AM - 11:30 AM

PDSVISION UK Ltd is the first and only UK & Ireland Moldex3D Authorised Certification Centre. In this course, you will learn features, functionalities and workflows in Moldex3D using both eDesign and BLM meshes. The format of the course is a mix of theory and practical workshop exercises.

10 - 11 Dec 2024

2 days

This course covers the use of Ansys LS-DYNA inside Workbench. Ansys LS-DYNA is useful for the analysis of problems involving contact, large deformation, nonlinear materials, transient response, and/or problems requiring explicit solutions.

10 - 11 Dec 2024

6 hours 2 x 3 hour sessions

Learning or reviewing the fundamentals of computational fluid dynamics (CFD), including best practice, will enable you to get the most out of your own simulation software or assess the CFD undertaken by others with confidence.

10 - 11 Dec 2024

2 days

Learn how to create sheetmetal parts in Creo

Tue 10 Dec 2024

1 day

Failure Mode Effect Analysis is most effective when developed by a multi-discipline team that is facilitated by a skilled chairman. It is important that the chairman guides the team through analysis and ensures that effort is focused on achieving workshop objectives. This 1-day course covers the essential skills required to lead effective FMEA workshops.

10 - 11 Dec 2024

2 days

This course is designed to provide an overview of the overall safety lifecycle of instrumentation and control systems important to safety at Nuclear Power Plants (NPPs), focusing on Nuclear Safety and Security.

10 - 12 Dec 2024

3 days

Description This course is designed for new users who want to enhance their product design with simulation and analysis to reduce costly physical prototyping while increasing the products durability, reliability and safety.

10 - 12 Dec 2024

3 days

Learn common administration tasks in PDMLink

Wed 11 Dec 2024

1 day

Alarm Systems Management is a concise one-day training course aimed at helping prevent accidents similar to the explosion and fires at the Milford Haven refinery in the UK in 1994. This serious incident injured twenty six people, caused damage of the order of €50 million and resulted in the loss of a large amount of production.

11 - 12 Dec 2024

2 days

If your design will undergo any type of motion, the concepts presented in this course will equip you with knowledge critical to a successful design.

Wed 11 Dec 2024

1 day

Design of Experiments (DOE) is a procedure to planning, designing and analysing experiments to effectively and efficiently draw valid and statistically sound conclusions.

Wed 11 Dec 2024

1 day

Fault Tree Analysis is a top down, deductive failure analysis that identifies combinations of events that would lead to an undesired system event. This technique is mainly used in safety and reliability engineering to understand how systems can fail, to identify the best ways to reduce risk and quantify the probability of undesired events.

11 - 12 Dec 2024

6 hours 2 x 3 hour sessions

Learning or reviewing the fundamentals of finite element analysis (FEA), including best practice, will enable you to get the most out of your own simulation software or assess the FEA undertaken by others with confidence.

Wed 11 Dec 2024

1 day

ANSYS DesignXplorer software provides instantaneous feedback on all proposed design modifications, which dramatically decreases the number of design iterations and improves the overall design process.

Wed 11 Dec 2024

1 day

Life Data Analysis (also called “Weibull analysis”) is a statistical technique that is used to understand the lifetime of products. Product life can be measured in hours, miles, cycles or any other metric that applies to the period of successful operation. This technique is used across engineering sectors to quantify lifetimes for all manner of things, as well as to understand how aging will influence performance. The models created can then be used to estimate important life characteristics of the product

Wed 11 Dec 2024

1 day

This course provides a simple and practical view and appreciation for the assurance of software and programmable elements. The scope covers the decomposition of software requirements and the traceability to demonstration of compliance.

11 - 12 Dec 2024

2 days

System Reliability Modelling is the analysis of a System to understand its reliability, availability, maintainability performance. This is done through breaking the system down into subsystems, assemblies and components and their arrangement.Common methods use logic diagrams, such as reliability block diagrams (RBDs) and fault trees. ReliaSoft BlockSim provides a comprehensive platform for system reliability, availability, maintainability and related analyses using exact computations or discrete event simu

Thu 12 Dec 2024

1 day

The role of the Control Room Operator in managing risks of modern process plant is indisputable. Detecting deviations early, diagnosing the causes reliably and responding promptly and appropriately all contribute to the avoidance of major accidents and reduces reliance on automated systems. To do this, Control Room Operators need to maintain good situational awareness. Their ability to perform this critical role will depend on them being healthy and alert.

Thu 12 Dec 2024

1 day

In this course you will learn about Creo Illustrate and its role as a purpose built, role based solution for creating 3-D Illustrations.

Thu 12 Dec 2024

1 day

Learn how to create an MBD model using a start part

Thu 12 Dec 2024

9:00 AM - 4:00 PM (7 hours)

Learn and achieve an understanding of the main tools in SpaceClaim to create a geometry from scratch or to clean up and prepare an imported geometry for modelling using Ansys solutions.

Thu 12 Dec 2024

1 day

Learn the rendering capabilities of Keyshot

Thu 12 Dec 2024

1 day

Asset Performance Management (APM) is a process that encompasses tools and procedures to maintain or improve an assets’ reliability, maintainability and/or availability with respect to its requirements, under its use environment, for the duration of its lifetime. APM is intended to be applied to an asset in an operational environment. Whilst many elements are involved in APM, Reliability Engineering is a central element to success.

16 - 19 Dec 2024

8 hours 4 sessions of 2 hours

Learn the fundamental skills necessary to unlock the power of nonlinear solutions in Ansys Mechanical. Understand the nonlinear solution algorithm and the end-to-end solution procedure that may be applied to all nonlinear analysis problems.

16 - 17 Dec 2024

2 days

New to Ansys Mechanical? This is the place to start. After completing this course you’ll understand the complete end-to-end procedure for conducting basic linear static structural analyses and will be able to apply it to the solution of your own analysis problems. Just as importantly, you’ll learn several techniques to improve the efficiency of your solutions and the fidelity of your results. You’ll also have a firm foundation for studying many advanced analysis techniques in Ansys Mechanical

16 - 17 Dec 2024

6 hours 2 x 3 hour sessions

ASME first issued a Boiler and Pressure Vessel Code (BPVC) almost 100 years ago to support safety requirements and encourage technology development. Today, ASME VIII is the most used code for designing pressure vessels, with 3 Divisions covering specific applications and approaches. Furthermore, ASME VIII is also frequently applied by engineers when assessing a wide range of other structures. Within ASME VIII, two complementary techniques for assessment are specified: Design by Rules Design by Analysis (D

16 - 17 Dec 2024

2 days

Creo Advanced Assembly Extension and Top-Down Design

16 - 18 Dec 2024

3 days

This comprehensive hands on course teaches core modelling skills -It is aimed at users of other CAD systems needing to learn Creo

16 - 18 Dec 2024

3 days

We recommend the 3-day Creo Parametric conversion course for those with experience in other 3D CAD systems starting to use Creo Parametric. From this course you will quickly gain confidence in creating models using Creo Parametric.

16 - 17 Dec 2024

1.5 days

Learn the Creo harness routing and documentation process.

16 - 17 Dec 2024

2 days

Learn how to use surfaces to create models in Creo.

16 - 18 Dec 2024

6 hours 3 x 2 hour sessions

Design for Reliability is a process that encompasses tools and procedures to ensure that a product meets its reliability requirements, under its use environment, for the duration of its lifetime. Design for Reliability is implemented in the design stage of a product to proactively improve product reliability, by seeking to minimise weaknesses in design.

16 - 18 Dec 2024

6 hours 3 x 2 hour sessions

Fault Tree Analysis is a top down, deductive failure analysis that identifies combinations of events that would lead to an undesired system event. This technique is mainly used in safety and reliability engineering to understand how systems can fail, to identify the best ways to reduce risk and quantify the probability of undesired events.

16 - 18 Dec 2024

6 hours 3 x 2 hour sessions

Failure Mode Effect Analysis is most effective when developed by a multi-discipline team that is facilitated by a skilled chairman. It is important that the chairman guides the team through analysis and ensures that effort is focused on achieving workshop objectives. This course covers the essential skills required to lead effective FMEA workshops.

16 - 18 Dec 2024

6 hours 3 x 2 hour sessions

Failure Mode and Effects Analysis (FMEA) is bottom up, inductive failure analysis that considers the effect that failure of lower level components and assemblies will have on the overall system. This technique is used across engineering to understand how systems can fail, the causes of failure and to identify the best ways to reduce risk.

16 - 18 Dec 2024

3 days, 9:00 AM - 5:00 PM

In this course you will learn the basic & advanced drawing operations of Arbortext Isodraw. You will also learn how to use the perspective & isometric tools & how to automate the creation of technical illustrations from existing 3D CAD data.

Mon 16 Dec 2024

1 day

Mathcad Prime Update from Mathcad 15 for experienced Mathcad 15 users

16 - 18 Dec 2024

3 days

The course includes configuring tools, fixtures and machining operations as well as learning how to create milling sequences, hole-making sequences and post process cutter location data to create machine code.

Mon 16 Dec 2024

1 day

This course provides a simple and practical view and appreciation for the assurance of software and programmable elements. The scope covers the decomposition of software requirements and the traceability to demonstration of compliance.

Tue 17 Dec 2024

1 day

Learn how to create animations in Creo.

17 - 19 Dec 2024

3 days

We recommend the 3-day Creo Parametric conversion course for those with experience in other 3D CAD systems starting to use Creo Parametric. From this course you will quickly gain confidence in creating models using Creo Parametric.

17 - 18 Dec 2024

2 days

Asset owners and their staff need to consider safety instrumented systems and safety instrumented functions as vital components within process safety. The risks to health, safety and the environmental are required to be reduced to an acceptable level, So Far As Is Reasonably Practicable (SFAIRP) or As Low As Reasonable Practicable (ALARP). It is also recommended that any commercial risk to companies should be reduced to acceptable levels for the relevant business.

Tue 17 Dec 2024

1 day

Learn to use MathCad for Maths

17 - 18 Dec 2024

2 days

Reliability Centred Maintenance (RCM) provides a structured framework for analysing the functions and potential failures for physical assets, with a focus on preserving system functions, rather than preserving equipment. RCM is used to develop scheduled maintenance plans that will provide an acceptable level of operability, with an acceptable level of risk, in an efficient and cost-effective manner.